WWW.SHARKCLEAN.COM
PRO
®
STEAM POCKET MOP
S3601A
OWNER’S GUIDE
English
11. DO NOT unplug by pulling on
power cord. To unplug, grasp the
plug not the power cord. Do not
use extension cords or outlets
with inadequate current carrying
capacity.
21. Extreme caution should be
exercised when using this
appliance to clean stairs.
22. Never use steam mop without
micro-fiber cleaning pad attached.
23. Keep your work area well lit.
12. DO NOT put any objects into
openings. Do not use with any
opening that is blocked.
24. Store steam mop indoors in a cool,
dry place.
13. DO NOT put hands or feet under
25. To avoid circuit overload, do not
operate another appliance on the
same socket (circuit) as the steam
cleaner.
the steam mop. Unit gets very hot.
14. Use ONLY on flat, horizontal
surfaces. Do not use on walls,
counters or windows.
26. DO NOT run appliance over
the power cord. If an extension
cord is absolutely necessary, an
extension cord rated a minimum
of 15 ampere, 14 gage cord should
be used. Cords rated for less
amperage may overheat. Care
should be taken to arrange cord so
that it cannot be pulled or tripped
over.
15. DO NOT use on leather, wax
polished furniture or floors,
synthetic fabrics, velvet or other
delicate, steam sensitive materials.
16. DO NOT add cleaning solutions,
scented perfumes, oils or any other
chemicals to the water used in this
appliance as this may damage the
unit or make it unsafe for use. If
you live in a hard water area, we
recommend using distilled water in
your steam mop.
27 Always unplug and allow the steam
mop to cool before removing or
changing mop heads.
WARNING: Your steam mop
is designed to clean hard floor
surfaces that will withstand high
heat. Do not use on unsealed wood
or unglazed ceramic floors. On
surfaces that have been treated
with wax or some no wax floors,
the sheen may be removed by the
heat and steam action. It is always
recommended to test an isolated
area of the surface to be cleaned
before proceeding. We also
17. When in use, NEVER turn the
appliance over or on its side.
NEVER DIRECT STEAM TOWARDS
PEOPLE, ANIMALS OR PLANTS.
18. NEVER LEAVE THE STEAM MOP
IN ONE SPOT ON ANY SURFACE
FOR ANY PERIOD OF TIME WHEN
MICRO-FIBER PAD IS ATTACHED
AS THIS WILL DAMAGE YOUR
FLOORS.
19. Carefully remove the micro-fiber
cleaning pad immediately after you
have unplugged and allowed the
steam mop to cool.
recommend that you check the use
and care instructions from the floor
manufacturer.
20.When cleaning the steam mop,
unplug the power cord from the
electrical outlet and clean with a
dry or damp cloth. Do not pour
water or use alcohol, benzene or
paint thinner on the unit.
This manual covers model number: S3601A 11
TECHNICAL SPECIFICATIONS
Voltage:
Power:
Water
120V., 60Hz.
1550 Watts
Capacity: 500ml (16.9 oz.)
TOLL FREE: 1-800-798-7398
English
Contents
Getting Started......................................................................2
Using Your Steam Mop .......................................................5
Using Your Carpet Glider...................................................9
Care of Your Steam Mop....................................................10
Troubleshooting Guide .......................................................12
Warranty...................................................................................13
Thank you for
purchasing
the Shark® Pro
Steam Pocket®
Mop.
1
Getting Started
When assembling your steam mop there
may be a little water in or around the
water tank. This is because we test all
our steam mops 100% before you buy
them, so you get a quality Shark® Pro
Steam Pocket® Mop.
h
i
a
c
b
l
j
d
k
m
e
f
g
a All-Purpose Mop Head (1),
h Quick Release Swivel Cord Wrap
and Triangle Mop Head (1)
i
j
Cord Clips
b Steam Mop Body
Water Tank Cap
c Mop Handle
k Water Tank
ON/Standby Switch
d Two-Sided Micro-Fiber Cleaning Pads
for the All-Purpose Mop Head (3),
and Triangle Mop Head (2)
l
m Mop Head Release Button
e (1) 6mm x 54mm Large Screw*
f
Filling Flask
*Phillips or flat head screwdriver can be
used. Screwdriver not included.
g Carpet Glider
2
TOLL FREE: 1-800-798-7398
English
fig. 1
IMPORTANT: First things first, always
make sure the mop is UNPLUGGED
from the wall when not in use.
ASSEMBLE
1
Insert the Mop handle end labeled
“Front” into the steam mop body.
Make sure it is inserted past the
line printed on the pole. Secure the
assembled handle and pole by using
the large screw and a Phillips or a flat
head screwdriver (screwdriver not
included). (fig. 1)
Never fill the mop, attach the mop
head, change or remove the micro-
fiber cleaning pad when the mop is
plugged into the wall. To prolong
the life of your Shark® Pro Steam
Pocket® Mop, we recommend using
distilled water. Make sure you only
add water to the tank. Chemicals or
cleaning solution may damage the
appliance and could be unsafe for
you and your family.
3
Getting Started - cont’d
fig. 2
fig. 4
fig. 5
fig. 3
IMPORTANT: Don’t use on unsealed
wood or unglazed ceramic floors.
On surfaces that have been treated
with wax or some no wax floors,
the sheen may be removed by
the heat and steam action. It is
always recommended to test an
isolated area of the surface to be
cleaned before proceeding. We
recommend that you check the use
and care instructions from the floor
manufacturer.
2
Use the lavender loop on the side of
the micro-fiber cleaning pad to slide
mop head into pad pocket. Then
secure the quick fasteners on the top
of the pocket to lock in place.
(fig. 2)
3
Snap the mop head into the base to
secure it. (fig. 3)
4
Turn the water tank cap counter
clockwise and remove from the tank.
(fig. 4)
Use the filling flask and pour water
into the tank. Please don’t overfill.
Replace the cap on the water tank.
(fig. 5)
4
TOLL FREE: 1-800-798-7398
English
Using Your Steam Mop
IMPORTANT: Make sure you don’t
use the mop without attaching a
micro-fiber cleaning pad and adding
water to the tank first. When you are
using the mop for the first time, it
might take longer than the normal 30
seconds to start steaming.
fig. 7
fig. 6
IMPORTANT: Your Steam Mop needs
water to make steam! Never use your
steam mop without water in the tank.
1
Pull and twist the quick release cord
holder to unwrap the power cord
completely. Plug into a 120-volt
electrical outlet. (fig. 6)
Sweep or vacuum your floors prior to
cleaning with your Steam Mop.
2
The ON/STANDBY switch will
flash blue. If the light does not turn
on, reference the troubleshooting
section on page 12. (fig. 7)
great quick cleaning products to
complement your Steam Mop, such
as the Shark® Navigator
(model NV350).
5
Using Your Steam Mop - cont’d
fig. 9
fig. 10
fig. 8
3
Press the ON/STANDBY button once
for dust setting (DUST lighted setting
indicator will illuminate). DUST setting
is light steam for a quick dusting and
best dry time. (fig. 8)
Press the ON/STANDBY button
a third time to activate the SCRUB
setting. SCRUB setting is for heavy
cleaning and will leave floors damp.
To better understand which steam
setting to use for your cleaning task,
turn to page 7.
Press the ON/STANDBY button
a second time to activate the
MOP setting. MOP setting is for
normal, everyday steam cleaning.
(fig. 9)
4
Clean your floors with a forward and
backward motion. (fig. 10)
Press the ON/STANDBY button until
the light flashes to stop the steam.
6
TOLL FREE: 1-800-798-7398
English
The Shark® Pro Steam Pocket® Mop has three unique steam settings so
you can use the perfect amount of steam for the cleaning task at hand.
See below for tips on when to use each setting.
Setting
DUST
Ideal for These Surfaces
Recommended Usage
Laminate
Bamboo
Hardwood
Marble
Light Cleaning and Dusting
Loosen and Lift Light Dirt
Sanitize Floors
Basic, everyday cleaning
Hardwood
Marble
Tile
Remove spots and smaller messes
MOP
Clean moderate and heavily-
trafficked areas
Stone
Sanitize floors
Hardwood*
Tile
Tough cleaning and removal of
stuck-on messes and stains
Deep clean heavily-trafficked areas
Cut through heavy dirt and grime
Sanitize floors
Stone
SCRUB
Linoleum
Carpet
Freshen area rugs and carpets
(with Carpet Glider)
* Scrub mode not recommended for continuous cleaning on hardwood
7
Using Your Steam Mop - cont’d
fig. 11
NOTE: Please wait 2-3 minutes for
5 When one side of the micro-fiber
cleaning pad gets dirty, just flip the
mop head and you can quickly start
using the other side. (fig. 11)
the Steam Mop to cool off before
removing the mop head or the
micro-fiber cleaning pad. Never leave
the steam mop with a damp/wet
micro-fiber cleaning pad on
any floor.
6 When the water tank is empty, the
steam mop will stop producing
steam. You can refill the water tank
at any time as long as the mop is
unplugged from the outlet. Follow
the instructions from page 4. This
applies to switching the mop heads
or micro-fiber cleaning pad as well.
8
TOLL FREE: 1-800-798-7398
English
Using Your Carpet Glider
The Steam Mop is great for
grooming and freshening
though it won’t clean your
carpet or area rugs.
fig. 12
fig. 13
THE CARPET GLIDER
2 Move the steam mop back and
1 The Carpet Glider can be used with
the all-purpose head to lightly steam
your carpet and area rugs. Just
place the mop head with micro-fiber
cleaning pad attached on top of the
glider. The recommended steam
setting is SCRUB when using the
carpet glider. (fig. 12)
forth across a section of the carpet.
The steam mop won’t clean your
carpeting or areas rugs, but it’s great
for grooming and freshening.
(fig. 13)
9
Care of Your Steam Mop
fig. 14
fig. 16
fig. 15
AFTER USE AND STORAGE
2
Empty the water tank before
1
When you have finished using the
steam mop, press the ON/STANDBY
switch until the LED light turns
flashing BLUE. This stops the unit
from steaming. Unplug the cord from
the outlet and place the mop into the
upright position. Let the unit cool for
2-3 minutes.
storage. Remove the water tank cap
and empty the tank over a sink.
Replace the water cap. (fig. 15)
3 To store the Shark® Pro Steam
Pocket® Mop hanging up, first
remove the head (after it has cooled
and the steam has been released)
then hang on a large hook. (fig. 16)
Remove the micro-fiber cleaning pad
by releasing the quick fasteners and
using the lavender loop on the side
of the pocket, avoiding contact with
the hot pad or dirt. (fig. 14)
10
TOLL FREE: 1-800-798-7398
English
To order additional parts and
accessories, feel free to contact
call 1-800-798-7398.
fig. 17
fig. 18
DECALCIFYING YOUR STEAM MOP
Calcium and mineral deposits can
build up and impact the performance
of your steam mop over time.
To extend the life of your product
we recommend that you use
distilled water or Shark®’s
Water Filtration Bottle.
CARE OF YOUR MICRO-FIBER
CLEANING PAD
1
We recommend washing your
micro-fiber cleaning pad separately
from other fabrics to avoid picking
up lint. Only use liquid detergent
(no powder detergent). Don’t use
any fabric softeners or bleach. Line
dry or dry on a low dryer setting.
(fig. 17)
2 If there are loose threads on the
micro-fiber cleaning pad carefully
cut the thread with scissors. Don’t
pull on them or cut at the base.
(fig. 18)
11
Troubleshooting Guide
PROBLEM
POSSIBLE REASONS & SOLUTIONS
Your steam mop should be securely plugged into a
120V AC electrical outlet only.
The Pro Steam
Pocket® Mop will
not turn-on.
Check your fuse or breaker.
If your unit still does not work, call 1-800-798-7398.
Is there water in the water tank? If not, add water to your steam
mop following instructions on page 4.
The unit will not
make steam.
If the unit still doesn’t make steam, follow the decalcification
instructions on page 11.
If you have already plugged in your unit, unplug and try a
different outlet. This may reset the standby mode.
Cannot select steam
setting/flashing blue
light remains on.
Add water to the tank and press the ON/Standby button to
select a steam setting.
If your unit still does not work, call Customer care at
1-800-798-7398.
Check to see if your micro-fiber cleaning pad is soaked through.
We recommend you unplug the steam mop and change the
micro-fiber cleaning pad.
The Pro Steam
Pocket® Mop leaves
water on the floor.
Make sure the micro-fiber cleaning pad is attached correctly.
Do not leave your steam mop on the floor with a damp or
wet cleaning pad.
The Pro Steam
Pocket® Mop left
a white spot on
the floor.
If you’re using tap water we recommend switching
to distilled water.
Make sure the cap is securely on the water tank.
The pad might be dirty, change the pad.
If you washed the cleaning pad with powder detergent, then
it might be ruined. Replacement pads are available at
sharkclean.com.
You might have left the mop in the same spot for too long.
Do you have hard water? If you do, you might want to switch
to distilled water.
Floors are cloudy,
streaky or spotty
after steaming.
This might be leftover from past cleaners used on the floor
surface. Use the steam mop a few more times and see if the
leftover cloudiness is removed. If this does not work, we
suggest rinsing the floor with water, letting it dry, and then
steam mopping again with a clean pad. One or more rinses
generally removes the residue. A more stubborn case may
require you to rinse the floor with a mix of one part vinegar
and two parts water.
The Pro Steam
Pocket® Mop is
hard to push.
Make sure the micro-fiber cleaning pad is attached correctly.
Check to see if the cleaning pad is excessively dirty. Replace if
the cleaning pad is too dirty or wet.
12
TOLL FREE: 1-800-798-7398
English
ONE (1) YEAR LIMITED WARRANTY
EURO-PRO Operating LLC warrants this product to be free from defects in material and
workmanship for a period of one (1) year from the date of the original purchase, when utilized for
normal household use, subject to the following conditions, exclusions and exceptions.
If your appliance fails to operate properly while in use under normal household conditions
within the warranty period, return the complete appliance and accessories, freight prepaid. For
If the appliance is found to be defective in material or workmanship, EURO-PRO Operating LLC
will repair or replace it free of charge. Proof of purchase date and $ 9.95 to cover the cost of
return shipping and handling must be included. *
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or
replacement of the unit at our option. This warranty does not cover normal wear of parts and
does not apply to any unit that has been tampered with or used for commercial purposes. This
limited warranty does not cover damage caused by misuse, abuse, negligent handling or damage
due to faulty packaging or mishandling in transit. This warranty does not cover damage or
defects caused by or resulting from damages from shipping or repairs, service or alterations to
the product or any of its parts, which have been performed by a repair person not authorized by
EURO-PRO Operating LLC.
This warranty is extended to the original purchaser of the unit and excludes all other legal and/
or conventional warranties. The responsibility of EURO-PRO Operating LLC warranty if any,
is limited to the specific obligations expressly assumed by it under the terms of the limited
warranty. In no event is EURO-PRO Operating LLC liable for incidental or consequential
damages of any nature whatsoever. Some states/provinces do not permit the exclusion or
limitation of incidental or consequential damages, so the above may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state or province to province.
*Important: Carefully pack item to avoid damage in shipping. Be sure to include proof of
purchase date and to attach tag to item before packing with your name, complete address and
phone number with a note giving purchase information, model number and what you believe
is the problem with the item. We recommend you insure the package (as damage in shipping
is not covered by your warranty). Mark the outside of your package “ATTENTION CUSTOMER
SERVICE”. We are constantly striving to improve our products, therefore the specifications
contained herein are subject to change without notice.
OWNERSHIP REGISTRATION CARD FOR
CANADIAN CONSUMERS ONLY
Please complete and return within ten (10) days of purchase. The registration will enable
us to contact you in the event a product defect is discovered. By returning this card you
acknowledge to have read and understood the instructions for use, and warnings set
forth in the accompanying instructions.
RETURN TO: EURO-PRO Operating LLC, 4400 Bois Franc, St. Laurent, Quebec H4S 1A7
PURCHASER: ……………………………………………………………………………………............................………............
ADDRESS: ………………………………………………………………………………………………...........................................
S3601A 11
DATE OF PURCHASE: ………………….........….. MODEL: ……………….....................................................
NAME AND ADDRESS OF STORE: …………………………………...........................………………………………..
13
U.S.:
EURO-PRO Operating LLC
Newton, MA 02459
Canada: EURO-PRO Operating LLC
4400 Bois Franc
Ville St. Laurent, Québec H4S 1A7
1-800-798-7398
COPYRIGHT© EURO-PRO OPERATING LLC 2011
PRINTED IN CHINA S3601A.E.110415
Illustrations may differ from actual product.
US Patent Nos. 7669280, 7600401, D611214, D626711,
D599518, D599517
|